X-Git-Url: https://defiant.homedns.org/gitweb/?p=ros_wild_thumper.git;a=blobdiff_plain;f=launch%2Fgps.launch;fp=launch%2Fgps.launch;h=0000000000000000000000000000000000000000;hp=aac62a7e064f8ee955a698d1244a6442c6adabb5;hb=f9cd8e0e872fdc7157c322d15dab71b0290d7633;hpb=9d3dd45801f2041d41f4325debebc3ccf4e3d0c2

diff --git a/launch/gps.launch b/launch/gps.launch
deleted file mode 100644
index aac62a7..0000000
--- a/launch/gps.launch
+++ /dev/null
@@ -1,164 +0,0 @@
-<?xml version="1.0"?>
-<launch>
-	<node pkg="gpsd_client" type="gpsd_client"  name="gpsd_client" output="screen">
-		<param name="use_gps_time" value="false"/>
-		<param name="frame_id" value="base_footprint"/>
-	</node>
-
-	<node pkg="robot_localization" type="navsat_transform_node" name="navsat_transform_node" output="screen">
-		<param name="magnetic_declination_radians" value="0.047"/>
-		<param name="yaw_offset" value="0.0"/>
-		<param name="zero_altitude" value="true"/>
-		<param name="broadcast_utm_transform" value="true"/>
-
-		<remap from="/imu/data" to="imu"/>
-		<remap from="/gps/fix" to="fix" />
-		<remap from="/odometry/filtered" to="odom_combined"/>
-		<remap from="/odometry/gps" to="gps"/>
-	</node>
-
-	<node pkg="robot_localization" type="ekf_localization_node" name="ekf_gps" clear_params="true" output="screen">
-		<!-- The frequency, in Hz, at which the filter will output a position estimate. Note that
-		the filter will not begin computation until it receives at least one message from
-		one of the inputs. It will then run continuously at the frequency specified here,
-		regardless of whether it receives more measurements. Defaults to 30 if unspecified. -->
-		<param name="frequency" value="10"/>
-
-		<!-- The period, in seconds, after which we consider a sensor to have timed out. In this event, we
-		   carry out a predict cycle on the EKF without correcting it. This parameter can be thought of
-		   as the minimum frequency with which the filter will generate new output. Defaults to 1 / frequency
-		   if not specified. -->
-		<param name="sensor_timeout" value="2.0"/>
-
-		<!-- If this is set to true, no 3D information will be used in your state estimate. Use this if you
-		   are operating in a planar environment and want to ignore the effect of small variations in the
-		   ground plane that might otherwise be detected by, for example, an IMU. Defaults to false if
-		   unspecified. -->
-		<param name="two_d_mode" value="true"/>
-
-		<!-- REP-105 (http://www.ros.org/reps/rep-0105.html) specifies three principal coordinate frames: map,
-		   odom, and base_link. base_link is the coordinate frame that is affixed to the robot. The robot's
-		   position in the odom frame will drift over time, but is accurate in the short term and should be
-		   continuous. The odom frame is therefore the best frame for executing local motion plans. The map
-		   frame, like the odom frame, is a world-fixed coordinate frame, and while it contains the most
-		   globally accurate position estimate for your robot, it is subject to discrete jumps, e.g., due to
-		   the fusion of GPS data. Here is how to use the following settings:
-		     1. Set the map_frame, odom_frame, and base_link frames to the appropriate frame names for your system.
-			  * If your system does not have a map_frame, just remove it, and make sure "world_frame" is set
-			    to the value of odom_frame.
-		     2. If you are fusing continuous position data such as wheel encoder odometry, visual odometry, or IMU data,
-			set "world_frame" to your odom_frame value. This is the default behavior for robot_localization's state
-			estimation nodes.
-		     3. If you are fusing global absolute position data that is subject to discrete jumps (e.g., GPS or position
-			updates from landmark observations) then:
-			  3a. Set your "world_frame" to your map_frame value
-			  3b. MAKE SURE something else is generating the odom->base_link transform. Note that this can even be
-			      another instance of robot_localization! However, that instance should *not* fuse the global data. -->
-		<!-- Defaults to "map" if unspecified -->
-		<param name="map_frame" value="gps"/>
-		<!-- Defaults to "odom" if unspecified -->
-		<param name="odom_frame" value="odom"/>
-		<!-- Defaults to "base_link" if unspecified -->
-		<param name="base_link_frame" value="base_footprint"/>
-		<!-- Defaults to the value of "odom_frame" if unspecified -->
-		<param name="world_frame" value="gps"/>
-
-		<!-- We already have a publisher for odom->base transform -->
-		<param name="publish_tf" value="true"/>
-
-		<!-- Use this parameter to provide an offset to the transform generated by ekf_localization_node. This
-		   can be used for future dating the transform, which is required for interaction with some other
-		   packages. Defaults to 0.0 if unspecified. -->
-		<!-- <param name="transform_time_offset" value="0.0"/> -->
-
-		<!-- The filter accepts an arbitrary number of inputs from each input message type (Odometry, PoseStamped,
-		   TwistStamped, Imu). To add a new one, simply append the next number in the sequence to its base name,
-		   e.g., odom0, odom1, twist0, twist1, imu0, imu1, imu2, etc. The value should be the topic name. These
-		   parameters obviously have no default values, and must be specified. -->
-		<param name="odom0" value="odom"/>
-		<param name="odom1" value="gps"/>
-		<param name="imu0" value="imu"/>
-		<rosparam param="imu0_queue_size">10</rosparam>
-
-		<!-- Each sensor reading updates some or all of the filter's state. These options give you greater control over
-		   which values from each measurement are fed to the filter. For example, if you have an odometry message as input,
-		   but only want to use its Z position value, then set the entire vector to false, except for the third entry.
-		   The order of the values is x, y, z, roll, pitch, yaw, vx, vy, vz, vroll, vpitch, vyaw, ax, ay, az. Note that not some
-		   message types lack certain variables. For example, a TwistWithCovarianceStamped message has no pose information, so
-		   the first six values would be meaningless in that case. Each vector defaults to all false if unspecified, effectively
-		   making this parameter required for each sensor. -->
-		<!-- x/y not included because of redundancy with velocities -->
-		<!-- vyaw not included in odom because too inaccurate -->
-		<rosparam param="odom0_config">[false,  false,  false,
-                                                false, false, false,
-                                                true, true, false,
-                                                false, false, true,
-                                                false, false, false]</rosparam>
-		<rosparam param="odom1_config">[true,  true,  false,
-                                                false, false, false,
-                                                false, false, false,
-                                                false, false, false,
-                                                false, false, false]</rosparam>
-		<rosparam param="imu0_config">[false, false, false,
-                                               false, false, true,
-                                               false, false, false,
-                                               false, false, false,
-                                               false, false, false]</rosparam>
-
-		<!-- The best practice for including new sensors in robot_localization's state estimation nodes is to pass in velocity
-		   measurements and let the nodes integrate them. However, this isn't always feasible, and so the state estimation
-		   nodes support fusion of absolute measurements. If you have more than one sensor providing absolute measurements,
-		   however, you may run into problems if your covariances are not large enough, as the sensors will inevitably
-		   diverge from one another, causing the filter to jump back and forth rapidly. To combat this situation, you can
-		   either increase the covariances for the variables in question, or you can simply set the sensor's differential
-		   parameter to true. When differential mode is enabled, all absolute pose data is converted to velocity data by
-		   differentiating the absolute pose measurements. These velocities are then integrated as usual. NOTE: this only
-		   applies to sensors that provide absolute measurements, so setting differential to true for twist measurements has
-		   no effect.
-
-		   Users should take care when setting this to true for orientation variables: if you have only one source of
-		   absolute orientation data, you should not set the differential parameter to true. This is due to the fact that
-		   integration of velocities leads to slowly increasing error in the absolute (pose) variable. For position variables,
-		   this is acceptable. For orientation variables, it can lead to trouble. Users should make sure that all orientation
-		   variables have at least one source of absolute measurement. -->
-		<param name="odom0_differential" value="false"/>
-		<param name="odom1_differential" value="false"/>
-		<param name="imu0_differential" value="false"/>
-
-		<!-- When the node starts, if this parameter is true, then the first measurement is treated as a "zero point" for all
-		   future measurements. While you can achieve the same effect with the differential paremeter, the key difference is
-		   that the relative parameter doesn't cause the measurement to be converted to a velocity before integrating it. If
-		   you simply want your measurements to start at 0 for a given sensor, set this to true. -->
-		<param name="odom0_relative" value="false"/>
-		<param name="odom1_relative" value="false"/>
-		<param name="imu0_relative" value="false"/>
-
-		<!-- If we're including accelerations in our state estimate, then we'll probably want to remove any acceleration that
-		   is due to gravity for each IMU. If you don't want to, then set this to false. Defaults to false if unspecified. -->
-		<param name="imu0_remove_gravitational_acceleration" value="true"/>
-
-		<!-- If you're having trouble, try setting this to true, and then echo the /diagnostics_agg topic to see
-		   if the node is unhappy with any settings or data. -->
-		<param name="print_diagnostics" value="true"/>
-
-		<remap from="odometry/filtered" to="gps_combined"/>
-
-		<rosparam param="process_noise_covariance">
-                       [0.01, 0,    0,    0,    0,    0,    0,     0,     0,    0,    0,    0,    0,    0,    0,
-                        0,    0.01, 0,    0,    0,    0,    0,     0,     0,    0,    0,    0,    0,    0,    0,
-                        0,    0,    0.06, 0,    0,    0,    0,     0,     0,    0,    0,    0,    0,    0,    0,
-                        0,    0,    0,    0.03, 0,    0,    0,     0,     0,    0,    0,    0,    0,    0,    0,
-                        0,    0,    0,    0,    0.03, 0,    0,     0,     0,    0,    0,    0,    0,    0,    0,
-                        0,    0,    0,    0,    0,    0.06, 0,     0,     0,    0,    0,    0,    0,    0,    0,
-                        0,    0,    0,    0,    0,    0,    0.025, 0,     0,    0,    0,    0,    0,    0,    0,
-                        0,    0,    0,    0,    0,    0,    0,     0.025, 0,    0,    0,    0,    0,    0,    0,
-                        0,    0,    0,    0,    0,    0,    0,     0,     0.04, 0,    0,    0,    0,    0,    0,
-                        0,    0,    0,    0,    0,    0,    0,     0,     0,    0.01, 0,    0,    0,    0,    0,
-                        0,    0,    0,    0,    0,    0,    0,     0,     0,    0,    0.01, 0,    0,    0,    0,
-                        0,    0,    0,    0,    0,    0,    0,     0,     0,    0,    0,    0.02, 0,    0,    0,
-                        0,    0,    0,    0,    0,    0,    0,     0,     0,    0,    0,    0,    0.01, 0,    0,
-                        0,    0,    0,    0,    0,    0,    0,     0,     0,    0,    0,    0,    0,    0.01, 0,
-                        0,    0,    0,    0,    0,    0,    0,     0,     0,    0,    0,    0,    0,    0,    0.015]
-                </rosparam>
-	</node>
-</launch>