import rospy
import tf
import struct
+import thread
import prctl
import spidev
from time import sleep
from diagnostic_msgs.msg import DiagnosticArray, DiagnosticStatus, KeyValue
from dynamic_reconfigure.server import Server
from sensor_msgs.msg import Imu, Range, BatteryState
-from wild_thumper.msg import LedStripe
from wild_thumper.cfg import WildThumperConfig
+from std_srvs.srv import SetBool, SetBoolResponse
WHEEL_DIST = 0.248
+BATTERY_CAPACITY_FULL = 2.750 # Ah, NiMH=2.750, LiFePO4=3.100
+UPDATE_RATE = 20.0
-class LPD8806:
- def __init__(self, bus, device, num_leds):
- self.spi = spidev.SpiDev()
- self.spi.open(bus, device)
- self.spi.mode=0b00
- self.spi.max_speed_hz=int(2e6)
- self.num_leds = num_leds
- self.latch()
- self.l = [(0, 0, 0)] * num_leds
- self.update()
-
- def set(self, i, red=0, green=0, blue=0):
- if red > 127 or green > 127 or blue > 127 or red < 0 or green < 0 or blue < 0:
- raise Exception("Bad RGB Value")
- self.l[i] = (red, green, blue)
-
- def latch(self):
- self.spi.writebytes([0x0 for i in range((self.num_leds+31)/32)])
-
- def update(self):
- l = []
- for i in range(self.num_leds):
- red, green, blue = self.l[i]
- l.append(0x80 | green)
- l.append(0x80 | red)
- l.append(0x80 | blue)
- self.spi.writebytes(l)
- self.latch()
-
-class MoveBase:
+class WTBase:
def __init__(self):
rospy.init_node('wild_thumper')
prctl.set_name("wild_thumper")
self.bMotorManual = False
self.set_speed(0, 0)
self.volt_last_warn = rospy.Time.now()
- rospy.loginfo("Init done")
i2c_write_reg(0x50, 0x90, struct.pack("BB", 1, 1)) # switch direction
- self.pStripe = LPD8806(1, 0, 12)
rospy.Subscriber("cmd_vel_out", Twist, self.cmdVelReceived)
- rospy.Subscriber("led_stripe", LedStripe, self.led_stripe_received)
rospy.Subscriber("imu", Imu, self.imuReceived)
+ rospy.Service('~manipulator_enable', SetBool, self.enableManipulator)
+ self.bDocked = False
+ self.bDocked_last = False
+ self.battery_capacity = BATTERY_CAPACITY_FULL*3600 # As
+ rospy.loginfo("Init done")
self.run()
def run(self):
- rate = rospy.Rate(20.0)
+ rate = rospy.Rate(UPDATE_RATE)
sleep(3) # wait 3s for ros to register and establish all subscriber connections before sending reset diag
reset_val = self.get_reset()
rospy.loginfo("Reset Status: 0x%x" % reset_val)
ir_count = 0
sonar_count = 0
+ i2c_write_reg(0x50, 0xA4, struct.pack("B", 1)) # enable Watchdog
while not rospy.is_shutdown():
rospy.logdebug("Loop alive")
+ #print "Watchdog", struct.unpack(">B", i2c_read_reg(0x50, 0xA4, 1))[0]
#print struct.unpack(">B", i2c_read_reg(0x50, 0xA2, 1))[0] # count test
self.get_motor_err()
self.get_odom()
- self.get_voltage()
+ self.get_power()
if ir_count == 0:
self.get_dist_left()
self.set_speed(self.cmd_vel[0], self.cmd_vel[1])
self.cur_vel = self.cmd_vel
self.cmd_vel = None
+
+ self.check_docked()
rate.sleep()
def execute_dyn_reconf(self, config, level):
self.bClipRangeSensor = config["range_sensor_clip"]
self.range_sensor_max = config["range_sensor_max"]
+ self.range_sensor_fov = config["range_sensor_fov"]
self.odom_covar_xy = config["odom_covar_xy"]
self.odom_covar_angle = config["odom_covar_angle"]
self.rollover_protect = config["rollover_protect"]
self.rollover_protect_limit = config["rollover_protect_limit"]
self.rollover_protect_pwm = config["rollover_protect_pwm"]
+ self.bStayDocked = config["stay_docked"]
return config
def imuReceived(self, msg):
- if self.rollover_protect and any(self.cur_vel):
+ if self.rollover_protect and (any(self.cur_vel) or self.bMotorManual):
(roll, pitch, yaw) = tf.transformations.euler_from_quaternion(msg.orientation.__getstate__())
if pitch > self.rollover_protect_limit*pi/180:
self.bMotorManual = True
msg.status.append(stat)
self.pub_diag.publish(msg)
- def get_voltage(self):
+ def get_power(self):
volt = struct.unpack(">h", i2c_read_reg(0x52, 0x09, 2))[0]/100.0
+ current = struct.unpack(">h", i2c_read_reg(0x52, 0x0D, 2))[0]/1000.0
msg = DiagnosticArray()
msg.header.stamp = rospy.Time.now()
stat = DiagnosticStatus()
- stat.name = "Voltage"
- stat.level = DiagnosticStatus.ERROR if volt < 7 else DiagnosticStatus.OK
- stat.message = "%.2fV" % volt
+ stat.name = "Power"
+ stat.level = DiagnosticStatus.ERROR if volt < 7 or current > 5 else DiagnosticStatus.OK
+ stat.message = "%.2fV, %.2fA" % (volt, current)
msg.status.append(stat)
self.pub_diag.publish(msg)
+ if volt < 7 and (rospy.Time.now() - self.volt_last_warn).to_sec() > 10:
+ rospy.logerr("Voltage critical: %.2fV" % (volt))
+ self.volt_last_warn = rospy.Time.now()
+
+ self.bDocked = volt > 10.1
+ self.update_capacity(volt, current)
+
if self.pub_battery.get_num_connections() > 0:
batmsg = BatteryState()
batmsg.header.stamp = rospy.Time.now()
batmsg.voltage = volt
- batmsg.current = float('nan')
- batmsg.charge = float('nan')
+ batmsg.current = current
+ batmsg.charge = self.battery_capacity/3600.0
batmsg.capacity = float('nan')
- batmsg.design_capacity = 5.0
- batmsg.percentage = float('nan')
+ batmsg.design_capacity = BATTERY_CAPACITY_FULL
+ batmsg.percentage = batmsg.charge/batmsg.design_capacity
batmsg.power_supply_status = BatteryState.POWER_SUPPLY_STATUS_DISCHARGING
batmsg.power_supply_health = BatteryState.POWER_SUPPLY_HEALTH_UNKNOWN
batmsg.power_supply_technology = BatteryState.POWER_SUPPLY_TECHNOLOGY_NIMH
+ batmsg.present = True
self.pub_battery.publish(batmsg)
- if volt < 7 and (rospy.Time.now() - self.volt_last_warn).to_sec() > 10:
- rospy.logerr("Voltage critical: %.2fV" % (volt))
- self.volt_last_warn = rospy.Time.now()
-
+ def update_capacity(self, volt, current):
+ if self.bDocked:
+ self.battery_capacity = BATTERY_CAPACITY_FULL*3600
+ else:
+ self.battery_capacity -= current/UPDATE_RATE
def get_odom(self):
speed_trans, speed_rot, posx, posy, angle = struct.unpack(">fffff", i2c_read_reg(0x50, 0x38, 20))
odom.child_frame_id = "base_footprint"
odom.twist.twist.linear.x = speed_trans
odom.twist.twist.linear.y = 0.0
+ odom.twist.twist.linear.z = 0.0
odom.twist.twist.angular.z = speed_rot
odom.twist.covariance = odom.pose.covariance
def get_dist_forward_left(self):
if self.pub_range_fwd_left.get_num_connections() > 0:
dist = self.read_dist_srf(0x15)
- self.send_range(self.pub_range_fwd_left, "sonar_forward_left", Range.ULTRASOUND, dist, 0.04, self.range_sensor_max, 30)
+ self.send_range(self.pub_range_fwd_left, "sonar_forward_left", Range.ULTRASOUND, dist, 0.04, self.range_sensor_max, self.range_sensor_fov)
def update_dist_forward_left(self):
if self.pub_range_fwd_left.get_num_connections() > 0:
def get_dist_backward(self):
if self.pub_range_bwd.get_num_connections() > 0:
dist = self.read_dist_srf(0x17)
- self.send_range(self.pub_range_bwd, "sonar_backward", Range.ULTRASOUND, dist, 0.04, self.range_sensor_max, 30)
+ self.send_range(self.pub_range_bwd, "sonar_backward", Range.ULTRASOUND, dist, 0.04, self.range_sensor_max, self.range_sensor_fov)
def update_dist_backward(self):
if self.pub_range_bwd.get_num_connections() > 0:
def get_dist_forward_right(self):
if self.pub_range_fwd_right.get_num_connections() > 0:
dist = self.read_dist_srf(0x19)
- self.send_range(self.pub_range_fwd_right, "sonar_forward_right", Range.ULTRASOUND, dist, 0.04, self.range_sensor_max, 30)
+ self.send_range(self.pub_range_fwd_right, "sonar_forward_right", Range.ULTRASOUND, dist, 0.04, self.range_sensor_max, self.range_sensor_fov)
def update_dist_forward_right(self):
if self.pub_range_fwd_right.get_num_connections() > 0:
self.start_dist_srf(0xb)
- def led_stripe_received(self, msg):
- for led in msg.leds:
- self.pStripe.set(led.num, red=led.red, green=led.green, blue=led.blue)
- self.pStripe.update()
-
+ def check_docked(self):
+ if self.bDocked and not self.bDocked_last:
+ rospy.loginfo("Docking event")
+ elif not self.bDocked and self.bDocked_last:
+ if not self.bStayDocked or self.cur_vel != (0, 0):
+ rospy.loginfo("Undocking event")
+ else:
+ rospy.loginfo("Undocking event..redocking")
+ thread.start_new_thread(self.redock, ())
+
+ self.bDocked_last = self.bDocked
+
+ def redock(self):
+ self.cmd_vel = (-0.1, 0)
+ for i in range(100):
+ if self.bDocked:
+ break
+ sleep(0.01)
+ self.cmd_vel = (0, 0)
+ if self.bDocked:
+ rospy.loginfo("Redocking done")
+ else:
+ rospy.logerr("Redocking failed")
+
+ def enableManipulator(self, msg):
+ rospy.loginfo("Set Manipulator: %d", msg.data)
+ i2c_write_reg(0x52, 0x0f, chr(msg.data))
+ return SetBoolResponse(True, "")
if __name__ == "__main__":
- MoveBase()
+ WTBase()
projects / ros_wild_thumper.git / blobdiff