+++ /dev/null
-<?xml version="1.0"?>
-<launch>
- <node pkg="gpsd_client" type="gpsd_client" name="gpsd_client" output="screen">
- <param name="use_gps_time" value="false"/>
- <param name="frame_id" value="base_footprint"/>
- </node>
-
- <node pkg="robot_localization" type="navsat_transform_node" name="navsat_transform_node" output="screen">
- <param name="magnetic_declination_radians" value="0.047"/>
- <param name="yaw_offset" value="0.0"/>
- <param name="zero_altitude" value="true"/>
- <param name="broadcast_utm_transform" value="true"/>
-
- <remap from="/imu/data" to="imu"/>
- <remap from="/gps/fix" to="fix" />
- <remap from="/odometry/filtered" to="odom_combined"/>
- <remap from="/odometry/gps" to="gps"/>
- </node>
-
- <node pkg="robot_localization" type="ekf_localization_node" name="ekf_gps" clear_params="true" output="screen">
- <!-- The frequency, in Hz, at which the filter will output a position estimate. Note that
- the filter will not begin computation until it receives at least one message from
- one of the inputs. It will then run continuously at the frequency specified here,
- regardless of whether it receives more measurements. Defaults to 30 if unspecified. -->
- <param name="frequency" value="10"/>
-
- <!-- The period, in seconds, after which we consider a sensor to have timed out. In this event, we
- carry out a predict cycle on the EKF without correcting it. This parameter can be thought of
- as the minimum frequency with which the filter will generate new output. Defaults to 1 / frequency
- if not specified. -->
- <param name="sensor_timeout" value="2.0"/>
-
- <!-- If this is set to true, no 3D information will be used in your state estimate. Use this if you
- are operating in a planar environment and want to ignore the effect of small variations in the
- ground plane that might otherwise be detected by, for example, an IMU. Defaults to false if
- unspecified. -->
- <param name="two_d_mode" value="true"/>
-
- <!-- REP-105 (http://www.ros.org/reps/rep-0105.html) specifies three principal coordinate frames: map,
- odom, and base_link. base_link is the coordinate frame that is affixed to the robot. The robot's
- position in the odom frame will drift over time, but is accurate in the short term and should be
- continuous. The odom frame is therefore the best frame for executing local motion plans. The map
- frame, like the odom frame, is a world-fixed coordinate frame, and while it contains the most
- globally accurate position estimate for your robot, it is subject to discrete jumps, e.g., due to
- the fusion of GPS data. Here is how to use the following settings:
- 1. Set the map_frame, odom_frame, and base_link frames to the appropriate frame names for your system.
- * If your system does not have a map_frame, just remove it, and make sure "world_frame" is set
- to the value of odom_frame.
- 2. If you are fusing continuous position data such as wheel encoder odometry, visual odometry, or IMU data,
- set "world_frame" to your odom_frame value. This is the default behavior for robot_localization's state
- estimation nodes.
- 3. If you are fusing global absolute position data that is subject to discrete jumps (e.g., GPS or position
- updates from landmark observations) then:
- 3a. Set your "world_frame" to your map_frame value
- 3b. MAKE SURE something else is generating the odom->base_link transform. Note that this can even be
- another instance of robot_localization! However, that instance should *not* fuse the global data. -->
- <!-- Defaults to "map" if unspecified -->
- <param name="map_frame" value="gps"/>
- <!-- Defaults to "odom" if unspecified -->
- <param name="odom_frame" value="odom"/>
- <!-- Defaults to "base_link" if unspecified -->
- <param name="base_link_frame" value="base_footprint"/>
- <!-- Defaults to the value of "odom_frame" if unspecified -->
- <param name="world_frame" value="gps"/>
-
- <!-- We already have a publisher for odom->base transform -->
- <param name="publish_tf" value="true"/>
-
- <!-- Use this parameter to provide an offset to the transform generated by ekf_localization_node. This
- can be used for future dating the transform, which is required for interaction with some other
- packages. Defaults to 0.0 if unspecified. -->
- <!-- <param name="transform_time_offset" value="0.0"/> -->
-
- <!-- The filter accepts an arbitrary number of inputs from each input message type (Odometry, PoseStamped,
- TwistStamped, Imu). To add a new one, simply append the next number in the sequence to its base name,
- e.g., odom0, odom1, twist0, twist1, imu0, imu1, imu2, etc. The value should be the topic name. These
- parameters obviously have no default values, and must be specified. -->
- <param name="odom0" value="odom"/>
- <param name="odom1" value="gps"/>
- <param name="imu0" value="imu"/>
- <rosparam param="imu0_queue_size">10</rosparam>
-
- <!-- Each sensor reading updates some or all of the filter's state. These options give you greater control over
- which values from each measurement are fed to the filter. For example, if you have an odometry message as input,
- but only want to use its Z position value, then set the entire vector to false, except for the third entry.
- The order of the values is x, y, z, roll, pitch, yaw, vx, vy, vz, vroll, vpitch, vyaw, ax, ay, az. Note that not some
- message types lack certain variables. For example, a TwistWithCovarianceStamped message has no pose information, so
- the first six values would be meaningless in that case. Each vector defaults to all false if unspecified, effectively
- making this parameter required for each sensor. -->
- <!-- x/y not included because of redundancy with velocities -->
- <!-- vyaw not included in odom because too inaccurate -->
- <rosparam param="odom0_config">[false, false, false,
- false, false, false,
- true, true, false,
- false, false, true,
- false, false, false]</rosparam>
- <rosparam param="odom1_config">[true, true, false,
- false, false, false,
- false, false, false,
- false, false, false,
- false, false, false]</rosparam>
- <rosparam param="imu0_config">[false, false, false,
- false, false, true,
- false, false, false,
- false, false, false,
- false, false, false]</rosparam>
-
- <!-- The best practice for including new sensors in robot_localization's state estimation nodes is to pass in velocity
- measurements and let the nodes integrate them. However, this isn't always feasible, and so the state estimation
- nodes support fusion of absolute measurements. If you have more than one sensor providing absolute measurements,
- however, you may run into problems if your covariances are not large enough, as the sensors will inevitably
- diverge from one another, causing the filter to jump back and forth rapidly. To combat this situation, you can
- either increase the covariances for the variables in question, or you can simply set the sensor's differential
- parameter to true. When differential mode is enabled, all absolute pose data is converted to velocity data by
- differentiating the absolute pose measurements. These velocities are then integrated as usual. NOTE: this only
- applies to sensors that provide absolute measurements, so setting differential to true for twist measurements has
- no effect.
-
- Users should take care when setting this to true for orientation variables: if you have only one source of
- absolute orientation data, you should not set the differential parameter to true. This is due to the fact that
- integration of velocities leads to slowly increasing error in the absolute (pose) variable. For position variables,
- this is acceptable. For orientation variables, it can lead to trouble. Users should make sure that all orientation
- variables have at least one source of absolute measurement. -->
- <param name="odom0_differential" value="false"/>
- <param name="odom1_differential" value="false"/>
- <param name="imu0_differential" value="false"/>
-
- <!-- When the node starts, if this parameter is true, then the first measurement is treated as a "zero point" for all
- future measurements. While you can achieve the same effect with the differential paremeter, the key difference is
- that the relative parameter doesn't cause the measurement to be converted to a velocity before integrating it. If
- you simply want your measurements to start at 0 for a given sensor, set this to true. -->
- <param name="odom0_relative" value="false"/>
- <param name="odom1_relative" value="false"/>
- <param name="imu0_relative" value="false"/>
-
- <!-- If we're including accelerations in our state estimate, then we'll probably want to remove any acceleration that
- is due to gravity for each IMU. If you don't want to, then set this to false. Defaults to false if unspecified. -->
- <param name="imu0_remove_gravitational_acceleration" value="true"/>
-
- <!-- If you're having trouble, try setting this to true, and then echo the /diagnostics_agg topic to see
- if the node is unhappy with any settings or data. -->
- <param name="print_diagnostics" value="true"/>
-
- <remap from="odometry/filtered" to="gps_combined"/>
-
- <rosparam param="process_noise_covariance">
- [0.01, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
- 0, 0.01, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
- 0, 0, 0.06, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
- 0, 0, 0, 0.03, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
- 0, 0, 0, 0, 0.03, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
- 0, 0, 0, 0, 0, 0.06, 0, 0, 0, 0, 0, 0, 0, 0, 0,
- 0, 0, 0, 0, 0, 0, 0.025, 0, 0, 0, 0, 0, 0, 0, 0,
- 0, 0, 0, 0, 0, 0, 0, 0.025, 0, 0, 0, 0, 0, 0, 0,
- 0, 0, 0, 0, 0, 0, 0, 0, 0.04, 0, 0, 0, 0, 0, 0,
- 0, 0, 0, 0, 0, 0, 0, 0, 0, 0.01, 0, 0, 0, 0, 0,
- 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0.01, 0, 0, 0, 0,
- 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0.02, 0, 0, 0,
- 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0.01, 0, 0,
- 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0.01, 0,
- 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0.015]
- </rosparam>
- </node>
-</launch>
projects / ros_wild_thumper.git / blobdiff